RFI XPOL MIMO 4G Panel Antenna - Ultra wide-band coverage 700 to 2700MHz - Pole mount bracket suits 25-50mm poles - Your choice of cable length and connectors (SMA or N-type) - Two cables for true MIMO operation - Wide spectrum design, suits all current and planned cellular networks (including 700MHz LTE). The brilliance of this antenna is it's wideband design - operating on three separate bands 650-960MHz, 1710-2170MHz, and 2300-2700MHz. With a 260 x 260mm design, this compact panel antenna will stand up to the challenge of ever-changing network frequencies for years to come. This is one of the few antennas on the market capable of covering the recently auctioned 700 and 2600MHz spectrum, as well as the current 1800MHz 4G, all the while being backwards compatible on all 2G and 3G voice and data networks.

Is this antenna for me?

Not sure if you'll get 4G? With an equally high gain on all other 2G/3G networks, you can still improve your current connection. With the Telstra 4G network expanding to cover 60% of Australia's population in 2013 this is an antenna you can buy with the reassurance of future compatibility. Take full advantage of the blistering fast speed the Telstra 4G network offers. If you're outside the official 4G 'coverage zone' or your modem keeps switching back over to Next-G, this antenna will help you lock on, or increase the signal strength and speed of your 4G connection.

Ideal for suburban and metro areas

Lower gain antennas are ideal for areas where hills and buildings are very close to your location. Buildings create a multipath environment - transmissions that bounce off walls or trees at an acute angle cause signal echos. Having travelled a further distance than a straight line transmission these signals are delayed, and to a simple receiver would be nothing more than interference. However thanks to clever technology used in cellular communications, multipath signals can recovered by your modem's RAKE combiner. A RAKE receiver consists of a series of sub-radios which read the incoming signal at different delay periods (typically one chip in WCDMA) and then combined to result in a higher quality signal. This antenna rests at ground potential, providing improved lightning protection and reduced precipitation static noise. Termination is via your choice of 'N' female coaxial connectors fitted to short cable tails, or SMA male connectors fitted to 10m LMR195 cables. If used as a 4G antenna we strongly suggest selecting the 500mm N Female option and using LCU400 extension cables due to the high attenuation losses on 4G.

Network Compatibility
Yes/No
Gain
Telstra 4GX (700MHz)
compatible
8.1dBi
Optus 4G+ (700MHz)
compatible
8.1dBi
Telstra Next-G™ (850MHz)
compatible
7.8dBi
Vodafone 4G+(850MHz)* *Please check Vodafone Coverage Map
compatible
7.8dBi
Optus Regional 3G (900MHz)* *Please check Optus Coverage Map.
compatible
7.2dBi
Vodafone Regional 3G (900MHz)* *Please check Vodafone Coverage Map.
compatible
7.2dBi
Telstra/Optus/Voda 4G (1800MHz)
compatible
6.5dBi
All carriers - Urban/Metro 3G (2100MHz)
compatible
6.9dBi
Optus 4G/Vivid Wireless (2300MHz)
compatible
7.5dBi
LTE-TDD Bands 38, 40 (2300MHz)
compatible
7.5dBi
802.11 b/g/n/ac WiFi (2400MHz)
compatible
8.5dBi
LTE Bands 7, 38 (2500-2690MHz)
compatible
8.5dBi

Electrical Specifications

Frequency Range: 650-960MHz / 1710-2170MHz / 2300-2700MHz Input Impedance: 50Ω VSWR: <2.5:1 / <1.6:1 / <1.6:1 Vertical Beamwidth: 70° / 100° / 80° Horisontal Beamwidth: 60° / 165° / 55° Front to Back Ratio: 11dB / 7dB / 12dB Cross Pol Isolation: 15dB / 18dB / 20dB Maximum Power: 4Watts

Mechanical/Environmental Specifications

Construction: Grey ABS Cable: 500mm tails or 10m LMR195 cables Connector: N-Type Female or SMA Male Wind Rating: 120km/hr Temperature: -40°C +70°C Weight: 1.55kg Dimensions: 260 x 260 x 95mm (L x W x D) Flammability: UL94-V0

Read More

 

 

 

What connection does this antenna have?

 

 

 

You can choose between 10m cables that terminate with SMA Male connectors, or short 50cm leads with N Female connectors. If 10m of cable is enough you can use the appropriate patch lead (make sure it has a SMA Female connector) to connect to your modem. If using this antenna with a mobile phone you will probably need an SMA to FME adapter to attach your phone's patch lead or cradle.

 

If you need to use more cable, or are using it on 4G, you'll need to select the N Female connector option so you can attach a super low loss cable (which have N Male connectors).

 

SMA male connector

 

Option 1. 2x SMA Male Connectors

 

n female connector

 

Option 2. 2x N Female Connectors

 

RFI wireless logo

 

(LTE-XPOL-002V)

SKU LTE-XPOL-002V
Shipping Weight 0.0450kg
Shipping Width 0.270m
Shipping Height 0.100m
Shipping Length 0.380m