Telstra Repeater Kit for Outback or Remote Areas – Indoor or Outdoor Coverage
SKU: CFG-T-O-W
Cel Fi Go Repeater Kit designed for Outback or Remote Areas
Key Features
-
Complete package with an Externally Mounted Donor Antenna, Cabling, Cel Fi Go Repeater & a Wall Mounted Distribution Antenna
-
Provides full service for up to 20 Telstra mobile phones or modems
-
4Gx(700MHz) or Next G(850MHz) frequency support (manual selection)
-
Suitable for Telstra, Boost, and Aldi Mobile networks
-
Currently Australia's only legal mobile phone repeater system.
Usage
-
The Cel Fi Go Repeater for the Telstra network is a convenient solution for those experiencing poor phone coverage inside the house or office
-
This is a complete repeater system designed for indoor coverage
-
Installing this device in your home can improve the reliability of phone calls, text messages, and increase 3G or 4G or 4GX services
-
The dual-band 700-850MHz Yagi antenna is ideal for rural areas where long transmission distances result in low signal - typically with the tower within 70-90km from your location
-
As this antenna does not operate on 1800MHz 4G, this kit is not suitable for urban areas
-
The repeater provides enough boost to create a 60m area of coverage within normal home or office environments - up to an impressive 100m area in open areas such as supermarkets or farms, as reported by our customers
-
Like all wireless systems, the coverage area is reduced by the signal travelling through thick walls or floors, so the actual coverage area will vary depending on your unique situation
-
The design of this repeater allows for greater flexibility - we can split the output signal across multiple antennas and even daisy chain the set up to another location
-
Please contact one of our sales team to discuss the potential options further.
A heads up!
-
This repeater unit is designed to provide 3G or 4G/x services to mobile devices, it cannot produce both networks concurrently.
Installation
-
The dual band Yagi antenna is connected to the repeater via a run of LCU400 cable with an SMA fitting, which allows the cable to directly connect to the Cel Fi Go’s input connector - from there, a smaller grade of LCU195 Cable is connected to the Cel Fi Go’s output, which is run to the location where you wish to install the ceiling mounted antenna.
-
Please note that the Distribution Antenna is directional with a 70°, so the antnena will only be able to provide coverage over an arc with little to no boosted cellular coverage existisng behind the Antenna
Similar kits
- We provide similar kits for suburban and metro areas suffering from poor coverage indoors despite good signal outdoors, and kits for hilly and regional areas.
Performance on 4G/4GX Internet
-
To provide the best and fastest Internet connection possible, a proper MIMO external antenna should be connected into a dedicated 3G/4G modem
-
Typical speeds through the repeater unit are around 25-30% of a dedicated modem.
Why is it legal?
-
Many mobile service providers do not support personal repeaters on their network, because of the interference they can cause when connected to the network, or when they are setup incorrectly
-
The Cel-Fi system is the only personal repeater that is widely approved by carriers in Australia
-
The Cel Fi Go is different to a standard repeater as it was designed to provide maximum coverage, is network friendly and easily installed. It does this by:
-
continuously monitoring power levels of the cell tower it is connected to, constantly adjusting its output power to suit the levels
-
only amplifying and disbursing a particular carrier’s mobile signal, operating within a set frequency band
-
giving the service provider the ability to shut down the repeater remotely if needed, using a signal from the base station
-
not interfering with the carrier’s network or other users on the network
-
having a unique installation process to eliminate feedback into the mobile network.
-
(CFG-T-O-W)
SKU | CFG-T-O-W |
Shipping Weight | 11.0000kg |
Shipping Width | 2.400m |
Shipping Height | 0.220m |
Shipping Length | 0.260m |
Shipping Cubic | 0.137280000m3 |