Optus Cel Fi Go Repeater Kit designed for Urban Areas

 

Key Features

 

  • Complete package with an External Donor Antenna, Cabling, Cel Fi Go Repeater & a Wall Mounted Distribution Antenna

  • Full service for up to 20 Optus mobile phones or modems

  • 4G+ (700MHz) or 3G (850MHz) or 4G (1800MHz) frequency support (manual selection required)

  • Optus, TPG, Amaysim, Dodo, iiNet, plus more

  • Currently Australia's only legal mobile phone repeater system

  • Custom terminated COL7195 & super low loss extendible cabling.

 

Usage

 

  • The Cel Fi Go Repeater for the Optus network is a convenient solution for those experiencing poor phone coverage within the house or office

  • Installing this device in your home can improve the reliability of phone calls, text messages, and increase 3G or 4G or 4G+ services

  • This is a complete repeater system designed to provide indoor coverage

  • The wideband collinear whip antenna is ideal for urban areas where there is signal available outdoors but it is poor indoors, typically there are a few towers within 10km from your location

  • The COL7195 antenna is connected to the repeater via a run of LCU400 cable with an SMA fitting, which allows the cable to directly connect to the Cel Fi Go’s input connector - from there a smaller grade of LCU195 Cable is connected to the Cel Fi Go’s output which is run to the location where you wish to install the ceiling mounted antenna

  • The repeater provides enough boost to create a 60m area of coverage within normal home or office environments - up to an impressive 100m area in open areas such as supermarkets or farms, as reported by our customers

  • Like all wireless systems, the coverage area is reduced by the signal travelling through thick walls or floors, so the actual coverage area will vary depending on your unique situation

  • This repeater's design allows for greater flexibility - we can split the output signal across multiple antennas and even daisy chain the set up to another location. Please contact one of our sales team to discuss the your options.

  • It's important to note that this repeater unit is designed to provide 3G or 4G/+ services to mobile devices, it cannot produce both networks concurrently. 

 

Installation

  • The Donor COL7195 Antenna is connected to the repeater via a run of LCU400 cable with an SMA fitting, which allows the cable to directly connect to the Cel Fi Go’s input connector - from there, a smaller grade of LCU195 cable is connected to the Cel Fi Go’s output, which is run to the location where you want to install the wall mounted antenna.

  • Please note that the Distribution Antenna is directional with a 70°, so the antnena will only be able to provide coverage over an arc with little to no boosted cellular coverage existisng behind the Antenna 

 

Similar kits

  • We provide similar kits for suburban and metro areas suffering from poor coverage indoors, despite good signal outdoors, and can provide customised kits with High Gain Yagi Antennas for rural areas, please contact sales@telcoantennas.com.au for more info.

 

Performance on 4G/4G+ Internet

  • To provide the best possible and fastest Internet connection, a dediacted MIMO external antenna should be connected into a dedicated 3G/4G modem

  • Typical speeds through the repeater unit are around 25-30% of a dedicated modem.

 

A heads up!

  • This repeater unit is designed to provide 3G or 4G/+ services to mobile devices, it cannot produce both networks concurrently. 

 

Why is it legal?

  • Many mobile service providers do not support the use of personal repeaters on their network. This is due to the interference they can cause when connected to the network, or when they are setup incorrectly

  • The Cel-Fi system is the only personal repeater that is widely approved by carriers in Australia

  • The Cel Fi Go is very different to a standard repeater, as it is designed to provide maximum coverage, be network friendly and easily installed by the end user. It does this by:

    • continuously monitoring power levels of the cell tower it is connected to, constantly adjusting its output power to suit

    • only amplifying and disbursing a particular carrier’s mobile signal, operating within a set frequency band

    • giving the service provider the ability to shut down the repeater remotely if needed, using a signal from the base station

    • not interfering with the carrier’s network or other users on the network

    • having a unique installation process to eliminate feedback into the mobile network.

 

Read More

(CFG-O-U-W)

SKU CFG-O-U-W
Shipping Weight 8.0000kg
Shipping Width 0.450m
Shipping Height 0.250m
Shipping Length 1.300m